Start with the sound and the slipper
If your VFD Twin transmission suddenly sounds rougher or feels gritty under load, the internal gears are the first place to look. But before you order parts, check one thing: is your truck running a VFD Slipper or a slipper lockout? The VFD Twin Sintered Gear Set is recommended for use with the VFD Slipper, not for use with a slipper lockout. That single compatibility rule decides whether this gear set is the right fix for your build.
The set replaces all internal gears of the VFD Twin Transmission, but it does not include the spur gear. If your noise or wear traces back to the spur gear, this set alone will not solve it.
What the VFD Twin Sintered Gear Set covers
- VFD Twin Sintered Gear Set: Replacement for all internal gears of the transmission. If you have confirmed wear inside the transmission, this set gives you a complete internal gear refresh rather than chasing individual gears.

VFD Twin Sintered Gear Set - VFD Twin Sintered Gear Set: Recommended for use with VFD Slipper, not for use with slipper lockout. Using this set with a slipper lockout is outside the recommended setup, so verify your slipper configuration before installing.
- VFD Twin Sintered Gear Set: Spur gear not included. Inspect the spur gear separately; if it is worn or damaged, you will need to address it in addition to this set.
Signs that point to internal gear wear
- New or worsening transmission noise: A whine or growl that changes with speed and load can come from worn gear teeth. Confirm the sound is coming from the transmission and not from the motor, spur gear, or driveline.
- Gritty feel or notchiness: If the transmission feels rough when you turn it by hand with the motor removed, inspect the internal gears for pitting, chipped teeth, or a polished wear pattern.
- Metal debris in the housing: Fine metallic sludge or sparkly oil inside the transmission case is a strong clue that gears are wearing. Clean the housing thoroughly before installing new gears.
- Visible tooth damage: Chipped, cracked, or sharp-edged teeth mean the gear is done. Sintered gears can wear gradually, so compare all internal gears rather than just the loudest one.
Rule out the cheaper causes first
Before you commit to a full internal gear replacement, check the easy external items: gear mesh at the spur gear, pinion tightness, bearing condition, and loose motor mount screws. A worn spur gear or a bad bearing can mimic internal gear noise. The VFD Twin Sintered Gear Set does not include the spur gear, so if the spur is the culprit, replacing the internals will not quiet the truck.
Also confirm your slipper setup. If you are running a slipper lockout, the recommended configuration for this gear set is a VFD Slipper. That does not mean the gears will fail instantly with a lockout, but the manufacturer’s recommendation points to the slipper as the intended setup.
A practical replacement sequence
- Verify slipper compatibility: Confirm you have a VFD Slipper installed, not a slipper lockout. This is the key compatibility check before installation.
- Inspect the spur gear: Since the spur gear is not included, check it for wear or damage. Replace it separately if needed.
- Clean the transmission housing: Remove all old grease and metal debris. Any leftover grit will accelerate wear on the new gears.
- Install the new internal gears: The set replaces all internal gears of the transmission. Follow your kit’s exploded views for shimming and order; the supplied information does not include a step-by-step procedure.
- Reassemble and check mesh: Turn the transmission by hand before powering up. It should turn smoothly without binding or roughness.
- Run a gentle break-in: The supplied information does not specify a break-in procedure, so start with light loads and listen for any new noise.
What the catalog does not tell you
The supplied information does not include gear material specifications, torque values, shimming instructions, or a break-in schedule. It also does not state a service life or wear limit. Treat any noise or roughness as a signal to inspect, and replace the internal gears when wear is visible or the transmission no longer runs smoothly.
If you are unsure whether your noise is internal or external, isolate it: remove the motor and spur gear, then turn the transmission by hand. If it still feels rough, the problem is inside.


