Back to Blog
Tips & Care 2026-11-15 Vanquish Products - Premium RC Crawler Kits & Accessories 0 views

RC Gear Grease Rock Lube: Where and How Much to Apply

RC Gear Grease Rock Lube: Where and How Much to Apply

A practical guide to applying Rock Lube on crawler gears and bearings: which spots benefit, how much to use, and what the product label does and doesn't confirm.

What Rock Lube is designed for

Vanquish Products RC Gear Grease Rock Lube is a synthetic grease blend made from high-quality base stocks with anti-wear additives. It is water resistant, clean, safe and non-toxic, and the label recommends it for lower-temperature gear, bearing and general-use applications. Each container holds two ounces.

That description points to a straightforward job: protecting metal-to-metal contact in a crawler drivetrain without turning the whole assembly into a grit magnet. The product is not a threadlocker, a sealant or a substitute for correct gear mesh, so treat it as lubrication rather than a fix for a worn or misaligned part.

Where Rock Lube earns its place on a crawler

Use the label's lower-temperature, gear-and-bearing recommendation as your filter. These are the spots where a water-resistant grease is most useful:

  • Ring and pinion gears: The gear teeth benefit from a thin, even film that stays put through slow, high-torque crawling. Apply after you have set mesh, not before.
  • Transmission gears: Spur and internal gears run in a closed housing where a light coating reduces metal-to-metal contact. A little goes a long way inside a sealed case.
  • Bearings: The label lists bearing use, so a small amount in exposed or serviceable bearings is supported. Keep grit out of the bearing first; grease on top of dirt just holds the dirt.
  • General pivot and contact points: The label's general-use wording covers low-temperature, low-speed contact points where a water-resistant film helps. Avoid using it as a universal spray on the whole rig.

The product facts that shape the application

  • RC Gear Grease Rock Lube: Synthetic grease blend with anti-wear additives, water resistant, clean, safe and non-toxic. Water resistance matters on a crawler that sees wet rock and mud; the clean, non-toxic description makes it easier to handle during routine maintenance.
    RC Gear Grease Rock Lube
    RC Gear Grease Rock Lube
  • RC Gear Grease Rock Lube: Recommended for lower-temperature gear, bearing and general-use applications. This is the label's own scope. Use it on gears and bearings in normal crawler running conditions rather than assuming it is a high-temperature or high-speed grease.
  • RC Gear Grease Rock Lube: Two-ounce container. Two ounces is enough for many re-greasing sessions on a crawler, so you can apply sparingly without worrying about running out mid-build.

A practical application sequence

The supplied product information does not include a manufacturer step-by-step procedure, so the sequence below is general workshop practice built around the label's stated uses. Check your kit's own manual for torque values and assembly order.

  1. Clean and inspect first: Wipe old grease and grit from the gear teeth or bearing. Look for pitting, chipped teeth or play before you add fresh grease; lubrication will not repair worn parts.
  2. Confirm the gear mesh: Set ring-and-pinion or transmission mesh according to your kit instructions before greasing. Grease applied over a bad mesh hides the problem rather than solving it.
  3. Apply a thin film: Use a small amount on a clean finger, brush or swab and spread it across the contact surfaces. The goal is a visible film on the teeth, not a packed cavity.
  4. Rotate and check coverage: Turn the gear or shaft by hand so the grease spreads across the full contact pattern. Add a little more only where the film looks dry.
  5. Wipe away excess: Remove grease that has pushed outside the gear or bearing area. Excess grease collects grit and makes future inspection messier.

How much is enough

A thin, continuous film is the target. For a ring and pinion, that means the tooth faces are coated but the valleys between teeth are not filled. For a transmission gear set, a light coating on the meshing surfaces is enough; a sealed housing does not need to be stuffed. For bearings, a small amount worked into the race is better than a blob sitting on top.

The label does not give a specific quantity or re-application interval, so use your own inspection to decide when to re-grease. If the film is still present and clean, you can leave it. If it has turned gritty or washed away, clean and reapply.

What the label does not tell you

The supplied information does not confirm a maximum operating temperature, a service interval, or compatibility with specific plastics and seals. If your crawler uses unusual materials or runs in extreme heat, check with the manufacturer before assuming Rock Lube is the right choice. The label's lower-temperature recommendation is a useful boundary, not a guarantee for every application.

It also does not list a full step-by-step procedure. Use your kit's assembly instructions for mesh settings and torque, and treat the steps above as a sensible way to apply the grease once the mechanical work is done.

Related Articles

Customer Service
Home
Products
Cart
Profile