Start with the part and the symptom
The front portal axle on a VS4-10 build uses stub shafts to carry drive from the portal gearbox out to the wheel. When one wears, the truck usually tells you before anything breaks: steering feels vague, the front end clicks or binds under load, or one wheel stops pulling while the other still drives. Those are the classic worn stub shaft symptoms RC crawler owners report, but they are not proof on their own.
The F10 Portal Front Stub Shafts are the replacement parts for those front portal axle assemblies. This listing is the Standard option, part number VPS08612, and it is listed under VS4-10 axle and chassis kit categories including VS4-10 Phoenix, Pro, and Ultra. Confirming that your build uses the F10 portal front axle is the first step; the second is deciding whether the shaft is actually the worn part.
What the Standard option covers
- F10 Portal Front Stub Shafts: F10 Portal Front Stub Shafts, Standard option, part number VPS08612. Match the part number on your order to the shaft you are replacing so you do not end up with a different option.

F10 Portal Front Stub Shafts - F10 Portal Front Stub Shafts: Listed under VS4-10 axle and chassis kit categories, including VS4-10 Phoenix, Pro, and Ultra. These are the builds the listing names, so check your kit against that list before ordering.
Symptoms worth investigating
Treat these as prompts to inspect, not a diagnosis. A worn stub shaft is one possible cause, and the supplied information does not list every failure mode or a test procedure for isolating it.
- Clicking or popping from the front axle: Noise that follows steering angle or load can point to wear in the front portal assembly, including the stub shaft. Check for play and visible wear before assuming the shaft is the source.
- One front wheel loses drive: If the truck pulls to one side under power or a front wheel stops contributing, inspect that corner's portal assembly. A stripped or rounded shaft end is one possibility among several.
- Binding or notchiness when turning: A shaft that binds at a specific steering angle deserves a close look. Rule out debris, damaged bearings, and loose hardware first.
- Visible wear at the shaft end: Scoring, rounded splines, or a loose fit where the shaft engages the portal are the most direct signs. Compare the suspect shaft with the opposite side.
Rule out the cheaper causes first
Before you order a replacement, inspect the whole front portal assembly, not just the shaft. Loose wheel hardware, a damaged bearing, a worn portal gear, or debris in the housing can produce the same symptoms. The supplied product information does not include a step-by-step diagnostic procedure, so use the symptoms above as a starting point and confirm the worn part visually.
If the shaft itself shows scoring, rounded splines, or a loose fit, the Standard F10 Portal Front Stub Shafts are the direct replacement. If the wear is elsewhere, replacing the shaft will not fix the problem.
A practical replacement check
The supplied information does not include torque values, disassembly steps, or a parts list for the portal assembly. The sequence below covers the checks the listing does support; follow your kit's own documentation for the mechanical work.
- Confirm the axle family: Verify that your VS4-10 build uses the F10 portal front axle. The listing names Phoenix, Pro, and Ultra, but check your specific kit before ordering.
- Confirm the option: This listing is the Standard option, VPS08612. If your build calls for a different option, this is not the right part.
- Inspect before you remove: With the truck on a stand, check for play, noise, and visible wear at the front portal. Note which side is affected.
- Replace and recheck: After fitting the new shaft, recheck for play and noise at the same steering angles that exposed the problem. If symptoms remain, the wear is elsewhere in the assembly.
What the listing does not tell you
The supplied information does not include installation instructions, torque specifications, or a maintenance interval for the F10 portal front stub shafts. It also does not confirm whether the Standard option is the only variant or how it differs from other options. Those are real limits on what this article can tell you, and they are worth knowing before you order.
What the listing does confirm is the part number, the option, and the VS4-10 builds it is listed under. Use those three facts to make the buying decision, and use your kit's documentation for the installation itself.


