Volver al blog
Guías prácticas 2026-11-17 Vanquish Products - Premium RC Crawler Kits & Accessories 0 vistas

H10 Aluminum Servo Mount: Install Steps and Fitment Notes

H10 Aluminum Servo Mount: Install Steps and Fitment Notes

Replace the molded servo mount on your H10 Optic or H10 front axle with the machined aluminum version. Fitment, color choice, and the install steps that matter.

What the H10 Aluminum Servo Mount replaces

The H10 Aluminum Servo Mount is a direct replacement for the molded servo mount that ships with the H10 Optic or the H10 Front axle set. If you are still running the stock plastic mount and want a machined aluminum part in that location, this is the swap. It is machined in the USA from domestic aluminum and comes as a single mount in the package.

This is a fitment-specific part, not a universal servo mount. The supplied compatibility list covers the VPS09010 H10 Optic RTR, the VPS09027 H10 Optic Kit, and the VPS08800 H10 Front Axle Set. Check your rig or axle part number against those three before you order.

Fitment facts to confirm before you start

  • H10 Aluminum Servo Mount: Direct replacement for the molded servo mount included with the H10 Optic or H10 Front axle set. You are replacing an existing mount in the same location, not adapting a different axle to take a servo.
    H10 Aluminum Servo Mount
    H10 Aluminum Servo Mount
  • H10 Aluminum Servo Mount: Compatible with VPS09010 H10 Optic RTR, VPS09027 H10 Optic Kit, and VPS08800 H10 Front Axle Set. These are the only compatibility references supplied; confirm your chassis or axle matches one of them.
  • H10 Aluminum Servo Mount: Package includes 1x H10 Machined Aluminum Servo Mount. One mount per package, so a second rig or spare axle needs its own unit.

Black or clear: pick before you open the package

The mount is offered in Black and Clear. Both are the same machined aluminum part; the difference is finish. Decide which one matches the rest of your H10 build before installation, because swapping color later means pulling the mount back off. If you are matching existing black anodized parts on the Optic, Black is the straightforward choice. Clear leaves the bare aluminum look visible.

Install sequence for the H10 servo mount

The supplied product information confirms what the part replaces and which vehicles it fits, but it does not include a step-by-step procedure or fastener specifications. The sequence below is a practical order for swapping a direct-replacement mount; follow your H10 manual for the actual fastener sizes and any axle disassembly steps.

  1. Confirm the part number: Match your rig against VPS09010, VPS09027, or VPS08800. If none of those apply, stop and verify fitment before removing anything.
  2. Support the rig and access the mount: Get the front axle to a comfortable working height and remove whatever covers the servo mount on your specific H10 build. The catalog does not list required disassembly, so use the H10 manual as your reference.
  3. Note the servo position before removal: Mark or photograph how the servo and horn sit in the stock mount. Reinstalling in the same orientation keeps your steering trim close to where it was.
  4. Remove the molded mount: Take out the fasteners holding the stock molded mount, then separate the servo from it. Keep the hardware organized; the package contains the aluminum mount only, not a fastener kit.
  5. Transfer the servo to the aluminum mount: Seat the servo in the new mount the same way it sat in the stock one. Check that the servo sits flush and the mounting holes line up before tightening anything down.
  6. Install the aluminum mount on the axle: Fit the mount to the H10 front axle in the stock location. Start fasteners by hand to avoid cross-threading, then tighten per your H10 manual.
  7. Reconnect and check steering: Reattach the servo horn and linkage, then cycle the steering through its full travel before running the rig. Listen and watch for binding or contact that was not there with the stock mount.

Checkpoints after the swap

  • Servo sits flush in the mount: The servo should seat the same way it did in the molded mount. If it rocks or sits proud, stop and find out why before tightening.
  • Steering moves freely lock to lock: Cycle the steering slowly and watch for the horn or linkage catching on the mount or axle. Any new contact means something is not seated correctly.
  • Fasteners stay tight through a run: Check the mount and servo fasteners after the first run. The catalog does not specify torque values, so follow your H10 manual and recheck rather than guessing.
  • Trim is close to your previous setting: If you reinstalled the servo in the same orientation, steering trim should be close. A large trim change usually points to the horn being off a spline or the servo shifted during install.

What the supplied information does not cover

The catalog confirms compatibility, material, color options, and package contents, but it does not list fastener sizes, torque values, or a full installation procedure. It also does not state performance differences between the aluminum and molded mounts beyond the material change. Use the H10 manual for hardware and torque, and treat any claim about stiffness or durability as unconfirmed by the supplied information.

If you are unsure whether your axle is an H10 Front Axle Set or a different Vanquish axle, check the part number on the axle or chassis before ordering. The H10 Aluminum Servo Mount is built for the three listed part numbers, and the catalog does not claim fitment beyond them.

Artículos relacionados

Customer Service
Inicio
Productos
Carrito
Perfil